3/8 vs 1/4 Air Hose

3/8 vs 1/4 Air Hose

When choosing an air hose, you have to consider the substance, length, and internal diameter. Also, consider the working environment, and the budget. Today we will evaluate two diameters of air hose 1/4 vs 3/8.

So, what’s the difference between 3/8 vs. 1/4 Air Hose? Many consumers prefer a ¼” hose to a ⅜” hose because it is lighter. It’s simpler to roll up, transport, and store. Of course, the fact that a 1/4-inch hose is less expensive than a 3/8-inch hose doesn’t hurt. A bigger interior diameter, like shorter hose lengths, will assist reduce frictional loss.

We will separate them into more eras in the following sections. Let’s get started!

What Are 3/8 Air Hoses?

A 3/8 inch air hose will have a 3/8 inch diameter, and this hose is usually sufficient for powering.

When working with high-powered equipment, you require a 3/8 hose. It is not suited for low-powered gadgets. If you have a big tank, you can still have a flow of more than 13.35 CFM as long as your outflow pressure remains over 90 PSI using a 3/8th ′′ hose.


  • A 3/8 air hose is highly adaptable to a variety of equipment.
  • A 3/8 hose allows for enough power and can be used with high-powered equipment.


As a high-end tool, it may be too heavy to use with a 3/8 air hose.

What Are 1/4 Air Hoses?

A 1/4 inch air hose will accurately measure 1/4 inch from underneath. 14” is the most frequent size fitting in air hoses. Get a 1/4 air hose if you’re planning to use it for lesser compressors, personal or home tasks.

Most people prefer a ¼” hose to a ⅜” hose because it is lighter. A 1/4 inch is also twice more minor than the size of a 3/8 inch air hose.


  • It is highly portable and adaptable.
  • A quarter-inch air hose is inexpensive and sufficient for light-duty applications.


It is not intended for use in high-end applications.

A Quick Comparison Chart: 3/8 vs. 1/4 Air Hose

Basis of Comparison⅜” Air Hose¼” Air Hose
MaterialRubber, PVC, hybrid, polyurethanepolyurethane, Hybrid, nylon, PVC
WeightA little heavyLight
Price$9 to $545$8 to $285
Dimension ⅜ inch¼ inch
Corrosion Resistance High Moderate
Temperature Tolerance-40℃ to 55℃
-30℃ to 50℃
Pressure resistanceMax 300 PSIMax 300 PSI

1/4 vs. 3/8 Air Hose: Detailed Key Differences

If you need an air hose for the pneumatic hammer or mining equipment. These hoses are recommended for your work. Let’s explore a little further in “difference between 1 4 and 3 8 air hose” for a more concrete concept.


What size air hose do I need? This is a common question, though. Usually, 1/4 inches is the most standard air hose size. This applies to both 1/4 and 3/8 inch air hoses. Because most 3/8 air hoses have 1/4 inch ends, most people utilize a 1/4-inch air fitting.

When it comes to transferring air pressure to the tool, the diameter and length of the hose go hand in hand. A 3/8 hose provides adequate space for flow. Moreover, you can follow the air compressor hose size chart for more ideas.

3/8 vs. 1/4 Air Hose: Hose Diameter

Hose inner dimension

The inner diameter of a 3/8 inch air hose is precisely 3/8 inches. A 1/4 inch air hose will accurately measure 1/4 inch from the inside. The 1/4 inch air hose is twice the size of a 3/8 inch air hose. 

Hose outer dimensions 

There is no industry standard for air hose OD. Air hoses are often abused. The outer diameter is determined by the manufacturer’s reinforcements and the material type utilized.


It is preferable to find the maximum CFM at the largest PSI. For a margin of safety, add 50% to the needed CFM and seek a compressor that satisfies the requirement.

Air hoses sold in stores are supposed to resist 300 PSI (pounds per square inch). However, for most tools, you should adjust the air pressure to 90 PSI. It will work with both 3/8 and 1/4 air hoses.


Rubber air hoses are the most flexible in cold weather and weigh one-third the weight of other air hoses. Rubber hose is the lightest, most durable, and most flexible hose available. Most of the PVC we’ve tested is stiffer and milder than rubber, making it difficult to twist.

These air hoses are made of hybrid, rubber, PVC, or polyurethane. Because the diameter is so small, you’ll probably have a hard time finding 1/4 rubber hoses.


You may purchase a 3/8 rubber hose for as little as $10, but keep in mind that 3/8 rubber hoses at this price are usually just 3 feet long. The same is valid with hybrid hoses. They may start as cheap as $10 for 3 feet. However, if you get a 3/8 polyurethane hose, the same amount may bring you up to 25 feet of hose.

I’ve seen nylon 1/4 air hoses for as little as $7 for 25 feet. You may purchase some hybrid hoses for as little as $15 for 25 feet.

Which Is Better: 3/8 or 1/4 Air Hose?

For 3 8 vs 1 4 air fittings, it all comes down to the tools. If you’re a hobbyist or do-it-yourselfer, your air pressure requirements will most likely be lower.

Nailers and staplers will require a quarter-inch or ¼” air hose. On the contrary, a ⅜” air hose is required for a 1/2 impact wrench. Even at 150 ft hose length, a 3/8 air hose on an air polisher can produce the necessary air pressure.

In the end, 3/8 air hoses will be adequate for more powerful instruments. A quarter-inch air hose is sufficient for light-duty applications.

What Size Air Compressor Hose Do I Need

You must decide which one demands the most CFM at the highest PSI. For a safety margin, add 50% to the needed CFM and seek a compressor that satisfies the requirement. If a device requires 3 CFM at 90 PSI, use a compressor that provides at least 4.5 CFM at 90 Pounds per square inch.

Best 3/8 Air Hose:

  1. Flexzilla Air Hose
Flexzilla Air Hose

Flexzilla is a ground-breaking hose made of a Flexible Hybrid Polymer material that redefines flexibility. 

It has remarkable all-weather versatility, ranging from -40°F to 140°F! Furthermore, it will not kink under strain and is lightweight and straightforward to handle. At 70°F, the maximum operating pressure is 300 psi.

  1. YOTOO Hybrid Air Hose
YOTOO Hybrid Air Hose

The YOTOO Hybrid Air Hose is perfect for garage, shop, industrial, household, and other applications. 

It comes with 1/4″ Commercial solid brass air fittings and Bend Restrictors already fitted. It is flexible from -40 to +150 degrees Fahrenheit, with a working pressure of 300 psi and a bursting pressure of 1200 psi.

  1. WYNNsky Hybrid Air Hose
WYNNsky Hybrid Air Hose

The Wynnsky Air Hose is ⅜-inch in diameter “25ft in length, and 25ft in diameter.

It has Dual Brass 1/4 “MNPT air fittings with a maximum operating pressure of 300 psi. Bend restrictors assist in minimizing kinking and extend the air hose life. Furthermore, its compact alloy end fittings will never rust and attach better than steel, aluminum, or zinc..

Best 1/4 Air Hose:

  1. Estwing E1450PVCR
Estwing E1450PVCR Air Hose

The Estwing E1450PVCR Rubber Hybrid Air Hose is built of durable hybrid materials.

It has all-weather protection and may be used in temperatures ranging from -40 degrees F to 164 degrees F. It also includes a rubber covering the rigid structure and a kink-resistant construction that extends the hose’s life.

  1. Metabo HPT Air Hose
Metabo HPT Air Hose

The Pneumatic Hose is intended for professionals who need a flexible, kink-resistant hose to tackle the most difficult duties. 

This item has a 300 PS burst ratio and a 3 to 1 burst proportion. It features a cold-resistant facility, which allows it to remain flexible in cold conditions. Furthermore, its spiral structure is strengthened for long-term endurance.

  1. YOTOO Hybrid Air Hose 1/4 inch kink resistant
YOTOO Hybrid Air Hose 1 4 inch kink resistant

This air hose is perfect for connecting supply routes, air tools, compressors, and other system components.

This component has 1/4″ Industrial air connections and Bend Restrictors attached. Surprisingly, it is flexible from -40 to +150 degrees Fahrenheit. It has a working capacity of 300 pounds per square inch and a burst pressure of 1200 pounds per square inch.


We’ve talked a lot about 3/8 vs. 1/4 Air Hose. I hope now you have a detailed notion.

A 3/8 hose is thus preferable if you have a range of strong ones in your workplace. For lightweight ones, a 3/8 air hose might be excessive.

If you’re a professional who works with solid instruments like an impact wrench daily, 1/4 air hose won’t suffice.

It can, however, be too hefty to function with a 3/8 air hose. Get a 1/4 air hose if you’re planning to use it for lesser compressors, personal or home tasks.

Leave a Comment

Your email address will not be published. Required fields are marked *